PRODUCTS ▬ EX1120

Nitek Long Range UTP Video System - EX1120

Extended Long Range Active Video Balun System -

Selectable Distance Settings

Model Number: EX1120

  • Complete Extended Range Video System for UTP Cables
  • Includes Active Receiver & Active Transmitter
  • Selectable Receiver & Transmitter settings - 100 to 12,000 ft (3,600 meters)

    • Live video transmission system for operation over twisted pair, Category 5, 6 or 7 cables.

    The EX1120 is a complete twisted pair video system made up of a TR1120 receiver unit and a TT1120 transmitter unit. The system is designed to operate over Category 2, 3, 4, 5, 6 or 7 twisted pair cable and will transmit over a range of 1,000 feet to 12,000 feet (3,600 meters) of UTP cable.. It works well over existing communication, computer network spare pairs, or new cable installations. A highly balanced transmitter output assures that the system will not interfere with other network equipment. Advanced receiver and transmitter electronics provide optimum video quality and complete immunity from ground loop, hum and noise. Both the transmitter and receiver provide adjustment for gain and frequency compensation allowing the system to be fine-tuned for the cable. These unique adjustments provide optimum performance over the entire operating range of the system and allow cable lengths to be estimated with a wide safety margin. The receiver and transmitter units each require 24 VAC power. In multiple receiver and/or transmitter applications a common power supply can be used for the system.

    • Active electronics compensate for frequency and level loss providing the highest quality video
    • High resolution color or monochrome video
    • Immunity to ground loop. Video and AC can be run in a common raceway, where code allows
    • Built-in protection from power surges, transients static or other electrical interference
    • Video can be run in the same cable with telephone and computer signals
    • Weather resistant design
    • Easy to install

    Applications:


    • Large Campus Installations
    • Shopping Malls
    • Airports
    • High Voltage Facilities
    • Traffic Around City Areas
    • Remote Gates

    Wire and Cable Recommendations

    Twisted Sender systems are recommended for use with unshielded twisted pair (UTP) wiring. The systems will operate over wire gauges from 26 AWG through 12 AWG but are optimized for 24 AWG. Category 2, 3, 4, 5, 6 or 7 cable may be used. Individually shielded pairs should be avoided, as they drastically reduce the operating range of the systems. Multi-pair cable (>15 pairs) with an overall shield is acceptable. Video can be operated in the same communication cable co-existent with telephone, computer, control signals, power voltages and other video signals. While video may be routed through telephone punch down block terminals, any bridge-taps, also called Ttaps and any resistive, capacitive or inductive devices MUST BE removed from the pair.


    For more specific information regarding wire types, gauges and proper installation techniques, please call (800) 528-4343 for technical assistance.
     Receiver Unit
    Size 1.6” (H) x 4.30” (W) x 2.4” (D)
    Power Requirements 24VAC@1watt (1VA)
    Input Balanced low voltage current loop
    Output 1 vpp composite video monochrome or color
    Common Mode Rejection >70dB
     Transceiver Unit
    Size 1.6”(4.1cm)H x 4.30”(11cm)W x 2.4”(6.1cm)D
    Power Requirements 24VAC@1watt (1VA)
    Input 1 vpp composite video monochrome or color
    Output Balanced low voltage current loop
    Common Mode Rejection >70dB
     System (2 Transceivers Required)
    Video Format RS170, NTSC, PAL, SECAM,
    CCIR (Color or B/W)
    Video Input 1 vpp composite video monochrome or color
    Operating Frequency 1 Hz to 10 MHz
    UTP Category Unshielded Category 2 or better
    Temperature Range -40 degrees C to +85 degrees C
    Shipping Weight 3 lbs

    Select a type of online documentation: